The hydraulic pressure generation makes a very high pressure possible.

The upper heating panel, led via four pillars, which remains stable during vulcanizing,
ensrues a parralel and highly condensed rubber mould (not spongy).

The rubber mould remains elastic permanently, since through vulcanizing
with the QUATTRO HYDRAULIC 200/160 a significantly higher density is obtained,
as reachable with a pneumatic vulcanizing press.

• Each heating panel has its separate regulation of temperature
• Dimensions of heating panels: 200 x 160 mm 

Technical Data

Voltage: 230 V
Power: 1000 W
Frequency: 50/60 Hz
Contact Pressure: 5 t
Dimensions (H x W x D): 510 x 330 x 230 mm
Weight: ca. 47 kg

Our manual Vulcanizing Presses* QUATTRO PARALLEL VP 200 features
an upper heating panel that is moved downwards by an easily rotatable
handwheel via four gears and four threaded spindles. As a result
the upper heating panel is moved parallel and remains perfectly stable
while vulcanzing, which ensures

a compact (not spongy) and parallel aligned rubber mould.

The rubber mould remains elastic permanently because a significantly higher
density is reached during the vulcanizing process.

During the whole pot life – this is the duration, in which the rubber is
deformable (liquid) and has a very high coefficient of expansion –
it is from great importance to reach very high forces:
that on e.g. a 110 x 90 mm rubber mould the hydraulic pressure
rises from 200 bar up to 400 bar.

In a pneumatic vulcanizing press this high pressure entails that the
heating panel opens and the aforementioned density during
pot life is compensated, which leads to unwanted results.

Advantages of the QUATTRO PARALLEL VP 200

• No more spongy rubber moulds and no more products of chance!
  Irrespective your vulcanizing frame lies centrally or laterally
  you will always obtain a 100% parallel, dense and stable rubber mould
• To minimize the heat transmission on the vulcanizing press,
  every heating panel has two thermal shields: a 10 mm mineral fibreboard
  and a circulated bridge, respectively
• The threaded spindles and gear wheels are made of high quality steel
• Each heating panel has a separate regulation of temperature

Technical Specifications

Diameter of Heating Panel: 200 mm
Space between Heating Panels: 125 mm
Maximum vulcanizing mould size: 120 x 100 mm

Dimensions (H x W x D): 650 x 430 x 230 mm
Voltage: 230 V
Power: 1300 W
Frequency: 50/60 Hz
Weight: ca. 46 kg

* On request we also deliver the

QUATTRO PARALLEL VP 250 and
QUATTRO PARALLEL VP 160

ECO MASTER RSC Vacuum Wax Injector with Digital Display

4 languages selectable (DE, GB, FR, ES); optionally expandable

Integration of the DOGENDORF codifying system

Any  kind* of non-codified rubber and silicon moulds can still be used:

• The moulds’ parameter sets are storable (for up to 50.000)
• Through ECO READ up to 200.000 parameter sets for moulds; option: ECO READ can be upgraded both to the ECO MASTER CC and ECOMAT 2000 CC

The cooling-down of the rubber mould can be achieved when the mould is still inside the receptacle.

2 clamp hand sizes available:

• 120 x 100mm – Standard Clamp Hand  (65 x 50 up to 120 x 100 mm moulds)
• 230 x 150mm – Memory Big Clamp Hand  (65 x 50 up to 230 x 150 mm moulds)

Values from 0.25 up to 1.5 bar may be adjusted by the potentiometer.

Technical Data

Dimensions (W x D x H):

• with Standard Clamp Hand 540 x 600 x 590 mm
• with Memory Big Clamp Hand 540 x 600 x 680 mm

Weight: 40 kg
Voltage: 230 V
Frequency: 50/60 Hz
Power input: 650 W

* Special forms of moulds can be used with receptacles especially made for.

The Device VINJECT CNC is an Automatic Vacuum Wax Injector
with Minimum Quantities Injection of Wax - Accuracy of 0.01g
(Latest Wax Injector Development, 2017) 

The fundamentally new, CNC controlled VINJECT CNC injector technology allows the injection of most precise volumes of wax in the rubber or silicon mould: The determination of the exact wax amount leads to the most exact results in wax injection. Accordingly, not only the wax leakage (too much wax) and the low injection (too little wax) doesn’t occur anymore. The VINJECT CNC makes the most efficient reproducability of wax pieces and therefore of the following casting parts possible.

Specifications

• Optimal reproducability and repeatability
• Entirely filled parts with rich surfaces, visually looking like pressed parts
• Overmoulding, dripping and undermoulding will be prevented
• Highest accuracy even of large-volume parts and most filigree details

Identification of Parameters

• An RFID tag is attached on the rubber or silicon mould
• ECO READ, the RFID reader attached on the clamp(ing) hand, identifies the RFID tags
• Easy coding of the mould’s parameters
• You can use your DOGENDORF Coding System,
  
  that means every  mould made for this system is applicable

Further Device Information

• Automatically controlled adhesion pressure and infeed
• Control (unit) with display and keyboard (4 languages – DE, GB, FR, ES)
• Maximum filling content of the kettle: 6 l
• Separate heatings for wax kettle and nozzle
• Wax temperature from 55 to 85 °C / 131 to 185 °F
• Values from 0.25 up to 1.5 bar may be adjusted by the potentiometer

2 Clamp Hand Sizes available:

• 120 x 100 mm – Standard Clamp Hand (65 x 50 up to 120 x 100 moulds)
• 230 150 mm – Big Memory Clamp Hand (65 x 50 up to 230 x 150 mm moulds)

Technical Data

Dimensions (H x W x D): 580 x 540 x 540 mm
Weight: 42 kg
Voltage: 230 V
Frequency: 50/60 Hz
Power input: 650 W